Advantages

• • Non-streaking
• • Durable surface
• • Will not peel or flake
• • Easy to use
• • VOC compliant
• • Moisture Vapor Tolerant
• Fast curing
• Protects against stains
• High gloss, will not fade
• Superior clarity
• Water-based
• Easy to maintain

Applications

The uniqueness and universality of its chemistry allow UPC Concrete-Finish to be used in many applications, including the following:

• Concrete Floors
• Terrazzo Floors
• Decorative Concrete
• Micro-Topping
• Self-leveling Cementitious Coatings

Colors

UPC Concrete finish is available in Clear only. (Product in liquid state is white milky color, then dries clear)

Packaging

UPC Concrete-Finish is available in the following packaging:

• 1 Gallon Pail
• 5 Gallon Pail
• 55 Gallon Drum
• 275 Gallon Tote

Product Data

Coverage:	1500 – 2500 SF /gal
	High Reflectivity 1500+ grit profiles
	1500 SF first application / 2500 SF
	second application
Cure time:	30-60 Minutes for Foot Traffic
	2 Hours for Vehicle Traffic
	Up to 14 Days for Full Properties
Critical recoat time:	15-30 Minutes if Burnishing
	30-60 Minutes if Not Burnishing
Shelf life:	1 Year

Concrete Preparation

Before coating is applied, concrete must be:

• Dry – No wet areas
• Clean – Contaminants removed
• Profiled – 200-3000 grit profile – Higher grit profiles will result in a higher gloss

Mechanical preparation is the preferred method of preparing concrete for coating application. Shot-blasting, diamond grinding, scarifying and scabbling are all acceptable methods.

Patching

Voids, cracks, and imperfections will be seen in finished coating if the concrete is not patched correctly. Patch concrete with UPC 777 Perfect Patch. After the patching material is cured, diamond grind patch.

Testing

All surfaces are not the same. It is recommended that a sample area be done before the start of the project. The test should be done on-site, using the proposed method by the assigned applicator to ensure desired finish.

Safety

Consult UPC Concrete Finish safety data sheet. Some individuals may be allergic to this coating. Use of safety goggles, protective gloves, and clothing when using this product is recommended.

Mixing

1. Shake or stir thoroughly before applying.

Application Instructions

Burnishing will renew the high gloss and wear protection properties of the treated surface, easily eliminating scuffs, heel and/or tire marks after initial treatment.

1. Thoroughly clean and vacuum the floor to prepare for sealer. Use a clean microfiber dust mop to dust the entire area. This will help prevent dust streaks in the coating.
2. Choose from 12-24” microfiber application pads. Select pad based on size of application area and applicator’s experience with coating.
3. Apply UPC Concrete Finish using a clean, pre-dampened microfiber pad and applicator. Apply at a rate of 1500-2500 SF per gallon depending on the surface profile, spreading material thinly and evenly so it completely covers the substrate. We recommend coating sections no larger than 20×20’ at one time.
4. Allow to dry for 10-15 minutes. Burnish/buff coating within 10-15 minutes once dry.
5. Burnish/buff with a high-speed machine (1500-2500 rpm) using a 3M™ White Super Polishing Pad. Burnishing individual coats is the recommended method to improve the curing process and overall shine. NOTE: If floor is not burnished, allow each application to dry at least 30-60 minutes before applying the next coat.
6. Repeat steps 3-4 depending on the surface profile and desired gloss levels. Repeated applications build a stain-resistant microfilm over the substrate. Do not over apply. It is important to apply very thin coats. If applied too thickly, material may not cure properly. The sealer may also become discolored, or leave streaks and/or applicator marks.
7. Avoid moisture for at least 72 hours. Do not allow standing water on the coating for 14 days. Covering the surface, even with protective sheeting, can cause the material to cure improperly and result in a cloudy or whitened effect.

Clean-up

Do not clean or scrub the surface for at least 72 hours after final application. Tools and equipment can be cleaned with water. Clean up any accidental spills immediately. This product is environmentally friendly. No special or hazardous disposal methods are required. Disposal of material must comply with all local, state and federal regulations.

Maintenance

Recommended maintenance includes regular sweeping and mopping of the treated surface. Washing and mechanical scrubbing with neutral pH cleaners/water are also recommended. DO NOT USE acidic, citrus or cleaners that contain butoxy-ethanol on the treated floor.

Additional Attributes

UPC Concrete Finish is a highly breathable sealer that allows for moisture vapor to escape at a slowed speed. Therefore this coating can be used on concrete with higher levels of moisture vapor without delamination or blistering occurring. When UPC Concrete Finish is used with UPC Lithium Densifier, it will slow the speed that the moisture vapor is driven through the slab and also help protect against Alkali buildup.

Product Limitations

UPC Concrete Finish is stain and chemical resistant however some chemical compounds such as acids may damage the surface. This coating is not intended to hide pre-existing stains, existing stains must be properly resolved prior to coating application. UPC Concrete Finish is not formulated for asphalt, non-cement surfaces or painted surfaces and will not alter the profile of the surface. Product is intended for interior use.

Coating systems are susceptible to cracking if the concrete moves or separates below the coating. Hence, joint and crack treatment should be reviewed prior to coating application. As a general rule, control joints (saw cuts) and random cracks should be saw cut or chased first then filled with Perfect Patch or similar approved hard epoxy product. Construction joints (two slabs that meet and hence move) should be treated. After the coating has been applied and cured, saw cut through the coating over construction joints and apply elastomeric caulking.

Warranty

Universal Polymer Coatings products are warranted for one year after date of application. Please refer to the UPC Limited Material warranty for additional clarification.

Safety

Consult UPC Concrete Finish safety data sheet. Some individuals may be allergic to this coating. Use of safety goggles, protective gloves, and clothing when using this product is recommended.